With the tremendous improvement in the wireless communication industry, the demand for emerging 5G technology ^{1 – 3} has increased for enhanced broadband and Internet of Things (IoT) applications. Today, many smart devices introduce intelligent behavior into households and industrial equipment to realize smart grids and smart homes/cities. For example, a smart energy meter can measure energy consumption by one device and send the data to the energy provider along with the end consumer statistics using two-way wireless communication technology. Although the existing 4G technology has served us well to date, it cannot satisfy the new challenges that can be brought by emerging wireless communication applications such as 5G smart grids, as a large amount of data transfer is needed at higher data rates with low latency. Hence, the adoption of 5G technology becomes more crucial. Therefore, worldwide research has started to implement this 5G technology by adopting techniques such as millimeter waves, small cells, massive MIMO, beamforming, and full duplexing. ⁴ However, the two major challenges to be solved while implementing this 5G technology for these applications are a reduction in energy consumption ⁵ and an enhancement in bandwidth. As the PAE of the power amplifiers ^{6 , 7} used in the R.F. transmitter plays the key role in deciding the energy consumption by the overall 5G wireless communication network, a power amplifier is needed that can provide improvement in PAE without compromising linearity and bandwidth. Many PA topologies have been reported previously ^{8 – 14} with various techniques to achieve linear amplification with high efficiency. Switching mode PAs such as Class-E/F demonstrate potential in providing excellent PAE but are not beneficial for enhanced bandwidth 5G applications because of their narrow bandwidth nature of harmonic terminations. On the other hand, linear mode PAs such as Class-A/B can achieve lower efficiency but are more linear than switching mode PAs. Nevertheless, Class-B mode PAs with harmonic tuning can theoretically achieve a peak efficiency of approximately 78.5%, and their bandwidth is also limited, as harmonic termination is difficult to realize over a wide bandwidth. However, this study mainly focuses on the design of a power amplifier that satisfies the requirements of smart grid wireless communication networks that ^{15 , 16} used for AMI of smart meters. A distributed communication architecture that can provide cost-effective and efficient communication is proposed in. ¹⁷ Distributed operation centers presently use 3G/4G cellular networks to communicate with data concentrators, which can be replaced by emerging 5G communication technology to support the increase in data traffic. A comprehensive review of 5G wireless communication networks for smart grids is presented in, ¹⁸ which motivates PA designers to design a PA that overcomes the bandwidth limitations of existing linear and switching mode PAs and satisfies the bandwidth requirements of 5G wireless communications in smart grids. A newly developed Class-J mode PA by S.C. Cripps in ¹⁹ has proven its potential to achieve high efficiency without compromising linearity and bandwidth. The design methodology for highly efficient, linear, and broadband Class-J PA mode is demonstrated in. ²⁰ Different Class-J mode PAs were reviewed to analyze their suitability for near-future 5G wireless communications used for smart grid applications. Of these PAs, the design of a 0.5 W GaN-based integrated Class-J PA that considers output matching network element losses for realizing on-chip output matching is presented in, ²¹ but because of the limitations of device technology and the low-Q on-chip matching network losses, its efficiency and output power are less than those of discrete PAs. An integrated Class-J PA using CMOS technology is presented in, ²² where the effect of knee voltage is considered to analyze 2nd harmonic losses for deriving modified design equations. However, the staked FET must be used for implementation because of the CMOS PA’s low breakdown voltage. The improvement in power output and D. E of a Class-J PA was presented in ^{23 , 24} by realizing a proper half-wave rectified sinusoidal waveform at the gate of the transistor. Apart from the usefulness of this method, it needs additional circuitry because of higher-order filters, which complicates the design and implementation of the PA. A methodology to improve the Class-J PA’s performance by injecting the active power at the 2 ^nd harmonic frequency has been proposed in, ²⁵ which causes an improvement in drain efficiency, but because of doubling and filtering, the design becomes complicated, and an increase in chip area makes it less appealing for integration. Based on the literature, it is understood that among the various modes of PAs, a Class-J PA can even satisfy the enhanced bandwidth requirement of the emerging 5G smart meter/smart grid applications without sacrificing linearity and efficiency if the appropriate matching networks are designed. Therefore, in this paper, a Class-J mode PA is chosen, and a design methodology is proposed to achieve the efficiency and bandwidth requirements of 5G wireless communications of smart grids. However, the important point to be considered when designing a PA for these smart grid applications is the frequency at which it has to be operated. Hence, different frequency bands, including LTE and 5G NR (new radio), ^{26 – 28} are analyzed to choose the appropriate operating frequency of the proposed Class-J PA. Recently, a frequency band termed citizen broadband radio service (CBRS) with 3.5 GHz center frequency (i.e., 5G sub6 GHz frequency) was allocated for public usage. ²⁹ This spectrum provides good space for 5G smart grid wireless communication applications. Hence, Initially, the proposed Class-J mode PA was designed to operate at a center frequency of 3.5 GHz (sub < 6 GHz) 5G frequency). The main contribution of this research paper involves the analysis of various matching network methods/topologies and the design of appropriate I/P and O/P matching networks to match a 50 Ω source and loads with the desired optimum source and load impedances of the transistor with respect to maximum PAE determined by load pull to achieve Class-J mode operation with the desired bandwidth of 5G smart grid specifications. The PA simulations were performed in the Advanced Design Systems (ADS) EDA tool, and this paper's structure is described as follows. A stepwise design procedure of a Class-J PA based on its theory with three approaches of lumped element-based input and output M. Ns for matching a 50 Ω source and load terminations with the transistor's optimum source and load impedances to obtain Class-J mode operation is described in the Methodology section. The schematic Class-J PA circuit simulation results as per the design methodology and their comparison with similar recent works are presented in the Results and Discussion sections. Finally, the advantages and limitations of this proposed research work are detailed in the Conclusions.

From the theory of the Class-J operation mode introduced and developed by S.C. Cripps, ¹⁹ the high-efficiency amplification in broadband can be obtained by terminating the output of transistor M ₁ to appropriate fundamental (Z _f0) and second harmonic (Z _2f0) optimal load impedances, as shown in Equations (1) and (2), at different frequencies over the desired bandwidth, as shown in Figure 2(a). Z f 0 = V DD − V th 1 + jα Imax / 2 = R opt + jα R opt (1) Z 2 f 0 = − V DD − V th jα 2 I max 3 π = − j 3 π 8 α R opt (2) where R _opt is the optimum resistance, which can be expressed as shown in Equation (3). R opt = 2 V DD − V th / I max (3)

With these optimum load impedances presented, in Figure 1, we can observe that the drain voltage (V _DS) is boosted with a phase shift.

Thus, the phase shift and boost in drain voltage (V _DS) cause a slight overlap with drain current (I _D), making the Class-J power amplifier highly efficient. Although this waveform shows the feature of a switching mode PA, the Class-J mode PA can provide linearity similar to the Class-B or AB modes because of its non-switching mode of operation. Unlike in Class-B, harmonic traps are unnecessary, making it suitable for wideband 5G applications.

The various steps involved in the design methodology of the proposed Class-J PA are discussed, as illustrated in the flowchart shown in Figure 2(b).

The Class-J PA is designed using a CGH40010F transistor with GaN technology in the Advanced Design System (ADS) EDA tool. Initially, after obtaining the bias (Q) point from the D.C. analysis, the stability analysis is performed on the CGH40010F GaN transistor with an S.P. network analyzer circuit, as shown in Figure 4. The unconditional stability of the device over the desired range of frequencies can be confirmed by checking the result on the stability factor and measuring the analysis represented using Figure 16 and Table 1. It is observed that the stability factor is >1, and the stability measure is >0, which ensures that the GaN device is unconditionally stable over the desired frequency range, i.e., (3–4) GHz.

After checking the device’s stability, the optimum impedances required for the Class-J PA can be obtained by conducting load d pull simulations, as shown in Figure 7, with reference to the target source and load impedances that are obtained from load-line analysis, as explained in step 4 of the Methodology section. The optimum source/input impedance obtained from the load-pull analysis is 6.315+j*13.787, and the load/output impedance obtained is 16.151-j*0.970, corresponding to the maximum power delivered (Pdel_dBm_MAX), as shown in Figure 17.

Similarly, the optimum source/input impedance obtained is 6.322+j*14.053, and the load/output impedance obtained is 16.212+j*4.793, corresponding to the maximum PAE of 66%, as shown in Figure 18.

From the results of load-pull analysis, the optimum input and output impedances corresponding to the maximum PAE are chosen for the Class-J PA design and tabulated by comparison with the target source and load impedances obtained from load-line analysis-based mathematical design equations, as shown in Table 2.

Before validating the optimum source and load impedances, the PA is terminated to a 50 Ω source and load terminals and the corresponding performance parameters, as shown in Figure 19.

Figure 19 shows that the performance parameters such as power delivered, large-signal and small-signal gains, D. E, and PAE are very low, as the CGH40010F GaN transistor does not terminate to optimum impedance values.

By terminating the transistor with the optimum impedance values obtained using load-pull simulations corresponding to the maximum PAE, harmonic balance S-parameter simulations are validated by running, as shown in Figure 8, and the respective performance parameters are shown in Figure 20.

From Figure 20, the performance parameters such as power delivered, large-signal and small-signal gains, drain efficiency and PAE are improved and nearly equal to the values obtained from load-pull simulations, as the input and output impedances of the CGH40010F GaN transistor are terminated to optimum impedance values. In addition, the reflection coefficients S (1,1) and S (2,2) are not as expected.

After validation of optimum impedances obtained from load-pull analysis, the M. Ns are designed as explained in step 7 of the Methodology section and placed at the respective input and output terminals of the PA, as Smith chart components are shown in Figure 13. Finally, these matching network elements are optimized and updated using an optimization tool in ADS, as shown in Figure 21.

After optimizing the performance parameters such as power delivered and large-signal and small-signal gains, PAE and D. E are shown in Figure 22. The reflection coefficients S (1,1) and S (2,2) are obtained as expected with the optimization of input and output matching networks.

The matching networks that are designed using L.C. bandpass match with the impedance matching utility, as explained in step 7 of the Methodology section, are placed at respective input and output terminals of the PA, as shown in Figure 14. Then, these matching network elements are optimized and updated using an optimization tool in ADS, as shown in Figure 23.

After optimizing the performance parameters such as power delivered and large-signal and small-signal gains, PAE and D. E are shown in Figure 24. The performance parameters are improved slightly with the optimization of the matching networks that are designed using the impedance matching utility.

The matching networks that are designed using basic L-type input and π-type output matching design equations, as explained in step 7 of the Methodology section, are placed at the input and output terminals of the PA, as shown in Figure 15, and then these matching network elements are optimized and updated using an optimization tool in ADS, as shown in Figure 25.

After optimizing the performance parameters such as power delivered and large-signal and small-signal gains, PAE and D. E are shown in Figure 26. The performance parameters are obtained as expected with the optimization of input and output matching networks.

All the numerical values of performance parameters such as power delivered (Pdel_W, Pdel_dBm_MAX) in watts and dBm, large-signal gain (LS_Gain_dB), PAE and D. E (Deff) that are shown in Figures 19, 20, 22, 24, and 26, corresponding to without and with three matching topologies, are computed with many equations using the “MeasEqn” of the harmonic balance HB simulator. The load voltage is plotted as the spectrum in dBm, and intrinsic voltages/currents are plotted as time-domain signals using an (HB) simulation controller in ADS. The desired half-rectified intrinsic drain voltage and currents with small overlap that represent the Class-J mode of operation were obtained, and reflection coefficients S (1,1) and S (2,2) > -10 dB over a frequency range from (3.3–3.7) GHz were observed from Figure 26. The comparison of the performance parameters of the Class-J PA with and without matching networks obtained for different source and load terminations is shown in Table 3.

The above comparison table shows that among the 3 methods used for matching networks, the Class-J PA with L-type input and π-type output matching networks exhibits expected performance parameters that are obtained from load-pull simulations (i.e., 66% of PAE and 40 dBm of max power output), as shown in Figure 18.

To validate the variation in the performance parameters with respect to the input power sweep, HB simulations were performed on the proposed Class-J PA by taking the available source power (Pavs_dBm) as the sweeping parameter. Figure 27 shows the simulation results of important performance parameters such as drain efficiency, PAE, large-signal gain, and power delivered corresponding to the available source power (Pavs_dBm) sweep. These results demonstrate that, a maximum power output of 41.4 dBm with a power gain of approximately 7.4 dB, max D. E of 82%, and max PAE of 67% for the corresponding available source power of 34 dBm with a 28 V power supply into a 50 Ω load.

Similarly, HB simulations were performed to validate the performance parameter variation of the proposed Class-J PA with L-type input and π-type output matching networks with respect to the input RF frequency, and the corresponding results are displayed in Figure 28. These results reveal that a power output above 40 dBm with a power gain of approximately 7 dB over a bandwidth of approximately 400 MHz (i.e., 3.3 GHz to 3.7 GHz) and max PAE and D. E of 67% and 82%, respectively, are obtained at a 3.5 GHz center frequency.

The variation of proposed Class-J PA’s D. E and PAE corresponding to its output power is illustrated in Figure 29.

It is observed that the PAE and Drain efficiency of the proposed Class-J PA are very low at low power levels and typically increase as the PA reaches higher output power levels and maintains high efficiency even at elevated power levels due to the efficient switching characteristics of GaN transistors and the design of Class-J mode, which helps minimize power dissipation.

The linearity of the proposed Class-J PA is another crucial parameter to evaluate its performance. In general, it can be evaluated using metrics like P1dB/P3dB (1 dB/3 dB compression point), third-order intercept point, AM-PM distortion, adjacent channel power ratio, etc. depending on its input signal and transistor technology used.

In this work, the proposed Class-J PA’s linearity is evaluated using a 3 dB compression point. Because it is designed using a GaN transistor as the main active device and fed by a continuous wave (CW)/1-tone signal as its RF input. The 3 dB compression point is defined as the point at which the gain of the PA begins to compress due to nonlinearity, and the output power no longer increases linearly with the input power.

According to the simulation findings, the gain of the proposed PA is compressed by 3 dB (from 12 dB to 9 dB), as shown in Figure 30. At this 3 dB compression point, the Pout value is 41 dBm, which is nearly as high as the saturated power (Psat) value (i.e., 41.4 dB), revealing the proposed Class-J PA’s linearity.

The proposed Class-J PA is designed and optimized for achieving efficiency. However, it offers good noise performance as it uses a GaN transistor, which generally exhibits low intrinsic noise characteristics compared to other semiconductor technologies like GaAs. This is due to GaN’s high electron mobility and low on-resistance, which contribute to better overall noise performance. In addition, the minimal impact of noise on the signal integrity is ensured by proper impedance M. Ns design and is validated through the linearity of the proposed PA.

Finally, the improved performance parameters of the proposed Class-J PA with L-type input and π-type output matching networks are compared with similar Class-J PAs in the literature. ^{30 - 34} As these PAs were designed at different frequencies and technologies, it is difficult to compare their performances. However, it can be noted that the Class-J PA design is proposed with a compact transmission line-based output matching network (OMN) in ³⁰ that uses the same transistor technology (GaN) of this work to obtain broadband and highly efficient amplification and achieves a maximum drain efficiency of 75%. Although our proposed PA is designed at different frequencies, its bandwidth is the same as that of this PA, and its transmission line-based M. Ns use a large chip area compared to the M. Ns of our work. A microwave Class-J PA for Wi-Fi IEEE802.11a Bluetooth applications designed with a methodology similar to that of this work in the same ADS EDA tool is presented in, ³¹ which uses a GaAs transistor as an active device but achieves a power output of 21 dBm and D. E of 69%. A fully integrated Class-J PA designed at 5 GHz for WLAN 802.11ax applications was presented in ³² that uses GaN on SiC technology with the same V dd=28 V to provide a maximum PAE of 55% and output power of 38 dBm, and it was mentioned that the performance of this PA can be enhanced further by employing DPD. However, the gain of this PA is high compared to our work, as it is designed as a multistage PA. A Class-J PA designed for X-Band is presented in. ³³ It uses the active load modulation technique, facilitates the PA's integrated implementation by eliminating the doubler and filter networks of conventional Class-J2 PAs, and achieves a drain efficiency of 71% and a PAE of 50%. However, the broad B.W. is not achieved because of harmonic tuners, and the auxiliary network used for phase shifting may need additional circuitry and space. A Class-J PA design with a novel direct M. N synthesis technique for broadband operation is presented in. ³⁴ The PAE and output power (dBm) are almost the same at the frequency (3.5 GHz) of our proposed work. Although the synthesis technique is novel, the transmission line-based MNs may occupy a large chip area. In addition, an integrated Class-J PA using CMOS technology is presented in, ²² in which the effect of knee voltage is considered for deriving modified design equations. However, the staked FET must be used for implementation because of the CMOS PA’s low breakdown voltage, whereas our work uses a GAN device with a high breakdown voltage.

The performance comparison discussed thus far is summarized in Table 4. The PAE and DE of this work are better, and the BW is comparatively lower than those of other works shown in Table 4. Because, in this work initially the proposed class J PA’s M. Ns are designed with a smaller number of lumped elements to obtain high efficiency, which leads to a bandwidth of 400 MHz with a centre frequency of 3.5 GHz. Although the BW obtained is comparatively lower than the existing Class-J PA designs in Table 4, it will be sufficient to implement the PA in emerging 5G wireless networks of smart metering/AMI applications. However, its BW can be enhanced further by replacing the passive lumped inductor with an AI through its tunability. We report that the proposed Class-J PA design of this work is not relatively efficient than other switching mode PAs. However, it has achieved a high efficiency without sacrificing the linearity over the desired BW compared with the existing author’s Class-J PA designs shown in Table 4.

In this work, the key factors such as efficiency, Pout, BW, and linearity of PA are considered to check its suitability for implementation in 5G wireless networks of smart metering applications. However, for its real-world deployment in 5G smart-meter wireless networks, the proposed PA’s chip area can be estimated to check its integration feasibility through the active element-based designs such as Active Inductor (AI) for its OMN.

The main contribution/novelty of this work involves designing of proposed Class-J PA’s M. Ns corresponding to 3.5 GHz centre frequency (sub 6 GHz 5G frequency) in 3 different ways using Smith chart utility, impedance match utility, and basic L-type and π-type impedance matching network design equations with an idea to replace the passive lumped inductor in its OMN with an AI, to achieve desired performance in terms of efficiency over enhanced B. W along with the linearity for making it suitable for emerging 5G wireless networks in smart metering or AMI applications.

A 3.5 GHz Class-J PA design with lumped element-based input and output matching networks that are suitable for 5G smart meter/grid applications is presented in this paper. The proposed Class-J PA design methodology is demonstrated in a stepwise manner. It is observed that with a small overlap between the intrinsic half-wave rectified current and voltage waveforms at the drain, this Class-J mode PA can be as linear as Class-B or AB modes because of its non-switching mode of operation. From the simulation results, we conclude that the proposed Class-J PA obtains a maximum drain efficiency of 82%, which is better than similar Class-J PAs reported in the literature. A PAE of 67% with a 13 dB small-signal gain at 3.5 GHz and an output power of 40 dBm (41.4 dBm peak) with a power gain of approximately 7 dB over a bandwidth of approximately 400 MHz (i.e., 3.3 GHz to 3.7 GHz) are achieved with no harmonic traps, unlike in Class-B mode PAs, which makes this Class-J PA superior to other PA modes and more appealing for emerging wireless communication networks used for AMI of smart meters in 5G smart grids. The proposed Class-J PA contributes to the overall functionality and performance of 5G smart metering applications by extending communication range through its high-power efficiency, increasing data transmission speed with wider BW, and improving reliability with reduced signal distortion. However, the PAE and BW of the proposed Class-J PA can still be improved by fine-tuning the designed matching networks and there is a scope for realizing the proposed Class-J PA with active element-based design to reduce its chip area and make it feasible for integration. This work is in progress to achieve the desired specifications of 5G wireless networks of smart grid applications.

No data are associated with this article.

Mr. Nagisetty Sridhar-original drafting of manuscript preparation, Dr Chinnaiyan Senthilpari-validation and Supervision, Dr. Mardeni R-cosupervision. All the authors agreed to the final version of this manuscript.