Ozone water or chloroxylenol: The comparison of disinfection effectiveness against the number of bacterial colonies in dental extraction instruments at the USU Dental and Oral Hospital

Introduction

Dental health workers are a group that is vulnerable to infection.¹ In dental practice, microorganisms can spread through blood, saliva or droplets through direct or indirect contact. One route of cross-infection due to indirect contact is tooth extraction instruments that have been contaminated with pathogenic microorganisms.²

Tooth extraction procedures have a high risk of infection transmission due to contact of the instruments with the patient’s blood and saliva.³ These must be aseptic at the time of tooth extraction to avoid bacterial infection, which is one of the complications that can occur as a result of tooth extraction.⁴

If the tooth extraction instrument is contaminated, microorganisms can be transmitted to dentists, nurses, or other patients who will be infected with diseases.⁴ According to the American Dental Association (ADA), it is estimated that dentists and patients may be exposed to around 40 types of infectious diseases when carrying out dental treatment procedures. Therefore, it is necessary to exercise prevention by disinfecting dental extraction instruments.²

Alternative materials for disinfection in dentistry have been developed. Ozone water can function as a disinfectant with the ability to oxidize amino acids and destroy proteins in the cellular membranes of microorganisms.⁵ Ozone water has the ability to kill pathogenic microorganisms and the resulting wastewater is safe to enter waterways.⁶ Chloroxylenol or para-chloro-meta-xylenol (PCMX) is a chemical-level disinfectant commonly used to disinfect skin and surgical instruments in dentistry.⁷ 4.8% chloroxylenol has a broad-spectrum antibacterial ability that can kill most bacteria and fungi. 4.8% chloroxylenol works by denaturing proteins, changing the permeability of cell walls and causing cell leakage. 4.8% chloroxylenol is one of the most widely used disinfectants in dentistry. 4.8% chloroxylenol is one of the phenol groups, and works by denaturing proteins, changing the permeability of cell walls and causing cell leakage.⁸

Research conducted by Ochie K and Ohagwu C in 2009 demonstrated that 3.5% sodium hypochlorite was the most effective in disinfecting x-ray equipment and accessories, followed by methylated spirit, 4.8% chlorocylenol, and 2% dichlorocylenol.⁹ A study by Igizeneza et al in 2020 revealed that 4.8% chlorocylenol was highly efficient in eradicating Staphylococcus sp and Streptococcus sp strains by 100%. Guther’s research in 2020, focusing on skin surfaces and hospital environments, discovered that 4.8% chlorocylenol could inhibit the metabolic activity of 38.9% of gram-positive bacteria and 60.7% of gram-negative bacteria.

Research on the effectiveness of ozone water (10 mg/L) as a disinfection agent on diamond burs that have been contaminated by S. aureus, E. coli, C. albicans and spores of B. atrophaeus showed a reduction of microorganisms by 90.15-99.33%. ⁹ Research on the effectiveness of 4.8% chloroxylenol as a disinfecting agent showed its ability to interfere with the metabolic activity of Gram-positive bacteria at 38.9% concentration and Gram-negative at 60.7% concentration.¹⁰

This study aimed to compare the effectiveness of ozone water and 4.8% chloroxylenol disinfectants on tooth extraction instruments, because these critical instruments have a high risk of causing infection as they penetrate the mucous membranes of the oral cavity.⁹

Methods

Study type

Figure 1 illustrates the research design we applied to evaluate the effectiveness of ozone water and chloroxylenol cleaning tooth extraction tools. This research was a laboratory experimental research with post-test-only control group designs. The study’s parameters include the concentration of ozone water (15 mg/L), the concentration of chlorosylenol (4.8%), the duration of immersion in ozone water (30 minutes), the duration of immersion in chlorosylenol (4.8%) solution (60 minutes), and the pre-research treatment. The patient’s oral cavity state, the kind and quantity of bacteria present there, the surrounding circumstances, and the instrument settings before tooth extraction are all non-parametric

Figure 1. Research design.

.

Results

This study consisted of 30 mandibular molar extraction forceps with three treatment groups, namely the mandibular molar extraction forceps group which was disinfected with ozonized water (Z), the mandibular molar forceps group which was disinfected with 4.8% chloroxylenol solution (K), and the mandibular molar pliers group which was rinsed with distilled water (A) as a negative control.¹⁴ Each group consisted of 10 mandibular molar extraction forceps.¹⁵

The 10 mandibular molar-removing forceps that were disinfected with ozonized water had a mean bacterial count of 4.00 ± 4.32 CFU/mL, showing they were still contaminated with pathogenic microorganisms with the highest number of bacterial colonies being 11·10³ CFU/mL.¹⁶ The 10 forceps which were disinfected with 4.8% chloroxylenol had a mean bacterial count of 16.00 ± 6.65 CFU/mL, showing they were still contaminated with pathogenic microorganisms, with the highest number of bacterial colonies being 27·10³ CFU/mL.¹⁷ Meanwhile, the mean bacterial count in the negative control group (Aquades) the 10 pliers extracting mandibular molars showed 217.50 ± 39.24 CFU/mL still forming bacterial colonies, with the highest number of bacterial colonies being 292 · 10 ³ CFU/mL (Table 1).¹¹

Based on the Kruskal Wallis statistical test results the effectiveness of ozone water, 4.8% chloroxylenol and negative control (Aquadest) on the number of bacterial colonies in mandibular tooth extraction forceps was significantly different, with a significance value of p = 0.000 (p < 0.05) (Table 2).⁴

Based on the results of a further using the Mann-Whitney U test comparing disinfection effectiveness between groups treated with ozone water disinfection and negative control (Aquadest), the significance value was p = 0.000 (p < 0.05).¹⁸ Ozone water was more effective as a disinfection agent compared to negative control on the number of bacterial colonies in dental extraction instruments at the USU Dental and Oral Hospital, as indicated by the lower average value of bacterial counts in the ozone water group, which was 4.00 ± 4.32 CFU/mL. In contrast, for the negative control group (Aquadest) the value was 217.50 ± 39.24 (Table 3).

Further Mann-Whitney U test results showed that there was a significant difference between the effectiveness of disinfection between groups treated with 4.8% chloroxylenol and negative control with a significance value of p = 0.000 (p < 0.05). 4.8% chloroxylenol was more effective as a disinfecting agent compared to negative control on the number of bacterial colonies in dental extraction instruments.¹⁹ The USU indicated that the average bacterial count value of the 4.8% chloroxylenol group was lower with 16 ± 6.65 CFU/mL, while the value for the negative control group was 217.50 ± 39.24 (Table 4).

Further Mann-Whitney U test results showed that there was a significant difference in effectiveness between ozone water and 4.8% chloroxylenol with a significance value of p = 0.000 (p < 0.05).²⁰ Ozone water was more effective as a disinfection agent compared to 4.8% chloroxylenol against bacterial colonies on dental extraction instruments, as indicated by the lower average bacterial count value of the ozone water group which was 4.00 ± 4.32 CFU/mL, while for the disinfection treatment group with 4.8% chloroxylenol, the value was 16 ± 6.65 CFU/mL (Table 5).²¹

Based on the results of data analysis from each treatment group, it was shown that ozone water was significantly more effective in disinfecting mandibular molar tooth extraction forceps compared to chloroxylenol 4.8% and negative control.²² Instruments in the 4.8% chloroxylenol group showed a smaller number of bacterial colonies than the negative control (Figure 2).

Figure 2. Total plate count 4.8% chloroxylenol, aquadest, and ozone water.

Discussion

This study compared two disinfection solutions, namely ozone water and 4.8% chloroxylenol. Ozone water is a strong alternative to disinfectants and effectively kills pathogenic microorganisms such as bacteria, viruses, fungi, protozoa, and endospores.⁶ Ozone is more effective against large numbers of microorganisms because of its ability to oxidize microorganisms without causing resistance. Ozone can inhibit the control of enzymes and therefore act on bacterial cell metabolism and damage bacterial cell membranes. Ozone water disrupts the integrity of the bacterial cell envelope through the oxidation of phospholipids and lipoproteins.

In this study, the concentration of ozone water used was 15 mg/L, with a soaking time of 30 minutes. The use of ozone water as a material for disinfecting dental instruments was recommended at a concentration of 10-20 mg/L. As reported by previous research, a concentration of ozone water that is too low showed a reduction in the antibacterial effectiveness of ozone water, while a concentration that is too high and exposure for too long could cause toxicity. Ozone maintained its antibacterial properties for the first 20 minutes, and after 30 minutes the stability of ozone water slowly decreased. After eight hours, there was no more ozone in the ozonized water.

Based on the data on the number of bacterial colonies in the treatment group with ozone water samples, ozone water was more effective in disinfecting the mandibular molar forceps. It was observed that four out of 10 mandibular molar extraction forceps were successfully decontaminated, with six samples showing bacterial growth with the highest number of bacteria being 11 × 10 ³ CFU/mL. The number of bacterial colonies in the treatment group with ozone water was the lowest when compared to the other two treatment groups, with an average value of 4.00 ± 4.32. This is due to the greater efficiency of ozone water in killing bacterial endospores by oxidizing and damaging the bacterial membrane which contains lipoproteins and fatty acids, so that the bacteria experience failure in the germination process.

In contrast, 4.8% chloroxylenol is unable to kill bacterial endospores, therefore 4.8% chloroxylenol is still classified as medium-level chemical disinfection. This makes ozone water more effective in killing microorganisms when compared to 4.8% chloroxylenol according to César et al., 2012, who stated that the antimicrobial activity of ozone water against B. atrophaeus spores resulted in a decrease in growth of 90.15% and 98.74% after 10 and 30 minutes of exposure to ozone water, respectively. In this study, the average number of bacterial colonies in the ozone water treatment group was lower due to the ability of the ozone water to kill bacterial endospores. Endospora is very resistant to high temperatures, extreme environmental conditions, or chemicals. The ability of ozone water to kill bacterial endospores was likely one of the causes of the fewer bacterial colonies formed in the ozone water treatment group. Data from César et al. also shows that the use of ozonated water (10 mg/L) for 30 minutes was effective for disinfection of diamond burs that have been contaminated by S. aureus, E. coli, C. albicans, and spores of B. atrophaeus, reducing bacterial contamination by 90.15-99.33%. In addition, based on Bezirtzoglou et al. found the research of César et al.¹⁰ states that a few teeth that have been soaked for 30 minutes with ozone water showed no bacterial colonies formed on the toothbrush. In the research by Nielsen et al., 2007, the addition of ozone to water that has been inoculated with S. aureus showed a reduction of 98.9%; S. faecalis, P. aeruginosa respectively were respectively reduced by 64.2% and 57.4%.²³ According to Xiao Hu et al., 2021, ozone water can eliminate severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) with an ozone concentration above 18 mg/L within one minute.¹² Wood et al. stated that ozone water can reduce fungal spores by 50.7-91.2%. Thus, ozone water can kill microorganisms in the form of bacteria, viruses, fungi, and bacterial endospores.²⁴

In the 4.8% chloroxylenol treatment group, there was bacterial growth in all mandibular molar tooth extraction forceps with a lower value compared to ozone water, but the number of bacterial colonies formed was less than the negative control. The mean bacterial count value in the 4.8% chloroxylenol group was 16.00 ± 6.65, while for the negative control group, the value was 217.50 ± 39.24. The research by Xiang et al. in 2018 showed that 11 out of 18 mandibular molar tooth extraction forceps which were cleaned using 4.8% chloroxylenol did not form bacterial colonies, and seven mandibular molar tooth extraction forceps had a maximum bacterial count of 812·10 ³ CFU/mL and the average number of bacterial colonies formed was 82.5. This is by the results of this study: in all research samples bacterial colonies still formed although with fewer bacterial colonies on average.²⁵ Liu et al., 2020, who researched the skin and the hospital environment, found that 4.8% chloroxylenol could interfere with the metabolic activity of Gram-positive bacteria by 38.9% and Gram-negative by 60.7%.²⁶ Mohammed AL-jaleel Khalil et al., 2023, showed that 4.8% chloroxylenol was effective in killing 100% isolates of Staphylococcus sp. and Streptococcus sp. Thus, 4.8% chloroxylenol was able to kill pathogenic microorganisms. Still, its effectiveness is lower when compared to ozone water. The -OH hydroxyl group of the 4.8% chloroxylenol molecule binds to proteins in the bacterial cell membrane to disrupt it, thereby allowing the contents of the bacterial cell to leak. This allows 4.8% chloroxylenol to enter the bacterial cell to bind more proteins and enzymes and deactivate cell functions. Meanwhile, the negative control group (Aquadest) had a lethal effect on microorganisms because distilled water is a neutral organic compound used as a pure solvent and does not have antibacterial activity.¹⁷

Differences in the number of bacterial colonies can also be caused by several factors, one of which is the number of microorganisms and contaminants, the condition of the patient’s oral cavity, the number and type of normal flora in the oral cavity of each patient which can differ due to severe caries, periodontal disease, pulpal necrosis or abscess. at the time of tooth extraction.⁴ Disinfectants have different abilities and susceptibility depending on the number and type of bacteria present in the patient’s oral cavity; the duration of exposure and the concentration of the disinfecting agents also affect the ability to kill microorganisms.⁸ The decrease in the number of different bacterial colonies in each treatment is also influenced by open environmental conditions, environmental temperature, and humidity both during sampling and when processing samples in the laboratory, ozone generator output, and operator negligence.

Conclusions

Ozone water was significantly more effective in disinfecting dental extraction instruments at USU Dental and Oral Hospital than 4.8% chloroxylenol with a significance value of p = 0.000 (p < 0.05). Ozone water can kill up to bacterial endospores while 4.8% chloroxylenol is not able to so it is still classified as a medium-level disinfectant.

Data availability